Model 2747-116-SA
Tap Holder

This holder is the non-releasing type. Provision is made for using a 5/8” diameter bushing 7/8” long.
Body length: 1-5/8”.

Model 2714-SA
Drill Holder

Solid-type drill holder can be used either rotating or stationary. Provision is made for using a 5/8” diameter drill bushing 7/8” long. Adjusting screw is provided in shank to prevent drill from slipping back. Body length: 1-1/8”.

Model 2714-IR-SA
Drilling and Chamfering Tool Holder

A drill holder with provisions for a 5/8” x 5/16” blade which is set on a 45° angle for chamfering. It can also be supplied with an auxiliary facing tool plate which takes a 5/16” x 3/8” blade for finish facing. Provisions are also made for using a 5/8” diameter drill bushing 7/8” long. Body length: 1-3/4”.

Model 2716-SA
Drill Holder with Stock Stop

This holder is designed for the first position. A hardened stock stop plate is furnished. Provision is made for using a 5/8” diameter drill bushing 7/8” long. Adjusting screw is provided in shank to prevent drill from slipping back.
Body length: 2-3/16”.

Model 2717-SA
Adjustable Drill Holder

Solid type drill holder can be used either rotating or stationary. Provision is made for using a 5/8” (15.88 mm) diameter drill bushing 7/8” (22.23 mm) long. Adjusting screw is provided in shank to prevent drill from slipping back.
Body length: 11/8”(28.58 mm).

Model 2720-SA
Centering & Facing Tool Holder

A solid drill holder with provision for blade to be used for facing. Provision is made for a 5/8” (15.88 mm) diameter drill bushing 7/8” (22.23 mm) long and a 3/8” (9.53 mm) square tool bit. A stock stop plate is furnished for use in the first position, which will permit the use of a form tool in the front cross slide. Holder can also be used in any other position. Adjusting screw in shank is provided to prevent drill from slipping back.
Body length: 2 7/16” (61.91 mm).

2726-R-SA: The capacity of this sizing tool holder is .075” to .500” (1.90 to 12.70 mm) diameter, 3/4” (19.05 mm) wide. It uses a circular tool and roll, which are made to suit the work. The tool and roll swing to insure same size work from all spindles. Sensitive adjustments are provided to obtain a high degree of accuracy. Width of holder is 13/8” (34.93 mm).

2726-R-SA: Same as 2726-R-SA except capacity is .262” to .812” (6.65 to 20.62 mm) diameter, 3/4” (19.05 mm) wide. Width of holder is 13/8” (34.93 mm).

Model 2729-SA
Knurl Holder

This is a single knurl holder for knurls 5/8” (15.88 mm) diameter, 1/4” (6.35 mm) wide with a 1/4” (6.35 mm) hole. Width of holder is 3/4” (19.05 mm).

Model 2730-SA
Knurl Tool Holder Double

This holder uses two knurls for either diamond or straight knurling. Knurl roll sizes for this holder are 5/8” (15.88 mm) diameter, 1/4” (6.35 mm) wide with a 1/4” (6.35 mm) hole. Width of holder is 11/4” (31.75 mm). This holder is also used for straightening.

Model 2730-23-SA
Knurl Tool Holder Wide, Oversize

This holder uses two knurls for either diamond or straight knurling. Knurl roll sizes for this holder are 3/4” (19.05 mm) diameter, 3/8” (9.53 mm) wide with a 1/4” (6.35 mm) hole. Width of holder is 1 1/4” (31.75 mm). This holder is also used for straightening.

Model 2768-SA
Rectangular Cutoff Tool Holder

This holder will accommodate all standard cut off blades from 1/32” (0.80 mm) to 1/8” (3.18 mm). The overall width of this holder is 5/8” (15.88 mm).

Model 2768-T-SA
Blade Cutoff Tool Holder

This holder will accommodate all standard width T blade cut off tools.

Model 2810-SA
Stock Stop

This stock stop attaches to a special tool clamp ring which is supplied. The assembly travels with the tool spindle. It is used generally with hollow mill in the first position. Furnished shank is 5 1/4” (133.35 mm) long to be turned to length required to suit hollow mill used.

Model 2763-10-SA
Adjustable Drill & Facing Tool Holder

This holder is an adjustable drill holder with provision for a blade to be used for facing. Drill can be centered independently of blade. Provision is made for using a 5/8” (15.88 mm) diameter drill bushing 7/8” (22.23 mm) long and a 3/8” (9.53 mm) square tool bit. A stock stop plate is furnished for use in the first position which will permit the use of a form tool in the front cross slide.

Holder can be used in any other position. Adjusting screw in shank is provided to prevent drill from slipping back.
Body length: 2 7/16” (61.91 mm).

Model 2785-1-SA
Box Tool Holder

Turning capacity of the box tool is 9/64” (3.57 mm) to 11/32” (8.73 mm) x 2 1/2” (63.50 mm) long or 11/32” (8.73 mm) to 1/2” (12.70 mm) diameter x 1 1/2” (38.10 mm) long. Provision is made for a 3/8” (9.53 mm) square tangent tool which can be set .015” (0.38 mm) ahead of the rolls or .110” (2.79 mm) behind the rolls. The tool holder is designed for the first position, being equipped with a stock stop, but can be used in any position. Two sets of roller rests, mounted on swinging arms are furnished. Shank is drilled for 3/8” (9.53 mm) center drill. Body length: 2 1/8” (53.98 mm).

Model 2862-10-SA
Adjustable Drill Holder

This is a short holder which clamps on the outside diameter of the 1 3/8” (34.93 mm) tool spindle for long work. This can be clamped on the outside of an E-2714 drill holder for short work. Provision is made for using a 5/8” (15.88 mm) diameter drill bushing 7/8” (22.23 mm) long. Length of holder body beyond end tool spindle is 7/8” (22.23 mm)

Model 3060-SA
1st Position Dovetail Tool Holder

This 1st position dovetail tool holder is designed for heavy cuts. This holder has a 10º face angle so the cutting tool is ground with a 10º angle plus the desired rake angle. The tool is set at approximately 10% of the smallest diameter ahead of center (above center). An American standard dovetail blank group #2, with a 1/4-20 NF tapped hole for a set screw is used. This screw takes the thrust as well as making the tool easy for adjustment.

Model 3060-10-SA
Dovetail Tool Holder

The same basic design as our 3060-SA with a 10º face angle with two tie down bolts for extra stability.

Model 3092-5-SA
2nd Position Dovetail Tool Holder

The same basic design as our 3060-SA with a 10º face angle with two tie down bolts for extra stability.

Model 3096-SA
Self Centering Tool Holder